How to Program a Dooya Motor

Pair the first remote

1. Press P1 on the motor for 2 seconds. The motor jogs once.
2. Release P1. The motor gives a long beep, ready to pair.
3. Within 10 seconds, press and hold STOP on the remote for 2 seconds. Two jogs and 3 beeps: paired.

If this remote is already paired, the same steps unpair it. The remote drops out of a setting after 10 seconds without a press, so wait for each jog or beep before the next step.

Reverse the direction

1. If UP runs the shade down and no limits are set yet, press and hold UP and DOWN together for 2 seconds. The motor jogs once.

Once limits are set, only P1 switches the direction: hold it for 10 seconds until the motor jogs 3 times, then release; it beeps 3 times.

Set the top and bottom stop points (limits)

1. Press UP for 2 seconds and bring the shade to the top position you want.
2. Press and hold UP and STOP together for 2 seconds. Two jogs and 3 beeps: top limit set.
3. Press DOWN for 2 seconds and bring the shade to the bottom position you want.
4. Press and hold DOWN and STOP together for 2 seconds. Two jogs and 3 beeps: bottom limit set.

Limit setting ends after 2 minutes without a press, and the limits stay stored when the power is off.

Add or remove a remote

1. On a remote that already works, press P2. One jog, one beep.
2. Press P2 again. One jog, one beep.
3. On the new remote, press and hold STOP for 2 seconds. Two jogs and 3 beeps: paired.

Without a working remote, press P1 for 2 seconds (one jog, then a long beep), then hold STOP on the new remote for 2 seconds. With either method, if this remote is already paired, the same steps unpair it. Adding a remote keeps the motor's settings. It stores up to 20 remote channels.

Set, use or delete the preferred position

The preferred (favorite) position is one stored stop between the limits; set both limits first.

1. Bring the shade to the position you want.
2. Press P2. One jog, one beep.
3. Press STOP. One jog, one beep.
4. Press STOP again. Two jogs and 3 beeps: position set.

To go there, press and hold STOP for 2 seconds. To delete it, press P2, STOP, then STOP again; the last press gives one jog and a long beep.

Change a limit

1. Press and hold UP and STOP (top) or DOWN and STOP (bottom) together for 5 seconds. One jog and a long beep.
2. Bring the shade to the new position.
3. Press and hold the same two buttons for 2 seconds. Two jogs and 3 beeps: stored.

Switch between jog mode and continuous mode

In jog mode, one press of UP or DOWN makes a short move; holding it more than 2 seconds runs the shade continuously.

1. Press and hold UP and DOWN together for 5 seconds. The motor jogs once.
2. Press STOP. One jog and a long beep means jog mode; two jogs and 3 beeps means continuous mode. Repeat to switch back.

Reset to factory settings

1. Press and hold P1 for 14 seconds, until the motor jogs 4 times.
2. Release P1. The motor beeps 4 times and is back in factory mode.
3. The motor now sleeps and ignores the remote. Press P1 for 2 seconds to wake it.
4. Pair a remote and set the limits again.

Charge the battery

• Before first use, charge the motor for 6 hours.
• Charge it through the charging port with a 5 V charger, at no more than 5 V, 2 A.
• The light blinks green while it charges and stays green when the battery is full.
• A red light blinking while the shade runs means the battery needs charging. Do not keep using the motor during a low-battery alarm; if the battery runs lower still, the motor stops until recharged.

Channels and batteries

• On a 15-channel remote, give each motor its own channel.
• JOG UP and JOG DOWN run only the channel the remote is set to.
• If the remote seems less sensitive or its range gets shorter, replace the batteries, using only the battery type Dooya specifies (two AAA).

On the DC2700AG, holding any button for more than 10 seconds stops the radio signal.